TorchLAB L3 L/M/H Triple - Three Level Drop In (3.0-9.5v)

Product Information

Triple LED Regulated 1100 lumen P60 Drop In

3 mode operation: low -> medium -> high -> low -> medium -> high ->
Turn power off, then on again within 3 seconds to change to the next level
Turn power off, then on again after 4 seconds to reset back to low
Automatically resets to low after power cycle exceeding 5 seconds (off/on) or battery change

FEATURES:

Fully regulated output between 4.8 and 9.5 volts
Below 4.8v it drops out of regulation and continues running until about 3v
Cell count detection and monitoring *new*
3.0/2.2 volt output reduction and cutoff *new*
Mode changes have a subtle transition effect (brief soft shifting)
Mode changes allow button presses as fast a 1/4 of a second
93% efficient driver with 2 lithium ion cells
Thermally-Enhanced Metal Core PCB
Integrated thermal safety protection at 65C (149F) *new*
Integrated thermal overheating protection at 120C (248F)
Shock and vibration tolerant materials and components
Heavy duty positive contact spring
Solid brass negative contact ring
Tight fit for best thermal contact with your SF or TL host
Shock proof materials, components, and design
Suitable for use in weapon mounted lights
Hard anodized black finish for superior thermal emissivity and durability
22 gauge mil-spec wire with 19 strand, silver-plated copper conductors, teflon insulated
Multiple independent LEDs for more output than single LED designs (even at the same wattage)

CAUTIONS:

Do not leave unattended while running
Do not run primary CR123 on high (100%). The boost driver will drain them harder and harder until the cells overheat, and may explode.
This light creates excessive heat
This light may cause eye damage
This light may burn the skin at close range
This light may cause combustibles to ignite
This light is not a toy, keep away from children

Recommended Switches:

Surefire Z41 with SF Twisty or Zero Rez or McClicky
Moddoolar Triad with SF Twisty or Zero Rez or McClicky
Zero Rez does not increase output
McClicky's should be Meidum or HARDpress with unsheltered boot (ie, Z41)

POWER SUPPLY OPTIONS:

Example setups.

Surefire 6P, C2, Z2:
      You can run 2xIMR 16340 for 20 minutes of runtime on high or 2xIMR 18350 for even more
      (not protected, be careful how far you discharge these cells)

Bored Surefire C3, 9P, or 6P + A19 extension:
      You can run 2 x protected 18500 for about 75 minutes of runtime
      (shuts off when depleted)

This drop-in runs well on 1, but is optimized for 2 rechargeable cells
      It will give full output until your cells are completely discharged

With a single lithium cell, It will run at approximately 75% output (800+ lumens) in this configuration. These are not regulated on 1 cell. A single AW 18650 2600mAh cell will provide an hour of runtime. You can run on a single 17670 for about 35 minutes.

MODELS:

Name       Voltage 2cell (1cell)*   Modes       Tint
Triple/60 L3c        1-2 cells    1100L (800L)    H-M-L    Cool
Triple/60 L3n        1-2 cells    1000L (700L)        H-M-L      Neutral

* Lumen outputs are LED rated values based on power, out the front values will be less

Universal Name Key: LEDcount / Format [space] Power Modes Tint
(not all options available on all models or formats)

LEDcount: 1 (single) or 3 (triple)
Format: 60 (drop in) or M2 (head)
Power: L (low) or H (high) or D (direct drive)
Modes: 1 (high) or 3 (high, medium, low)
Tint: C (cool) or N (neutral)