TorchLAB Triple v5 E/Scout Head - 7075 HA Natural

TorchLAB Triple v5 E/Scout Head - 7075 HA Natural

Product Information

TorchLAB Triple v5 E/Scout Head - 7075 HA Satin Natural

Control the Dark with the TorchLAB E and Scout head. A BOSS head, with smaller threading for all your Surefire E series applications. 7075 aluminum covered in a stunning satin-black hard anodized finish. And only 27g!

 

Suitable for both E and Scout applications:

 

 

Construction:

  • Lightweight 7075 structural aerospace aluminum
  • V5 Triple engine with thermally-enhanced metal core PCB
  • Shock and vibration tolerant materials and components
  • Solid brass electrical contact surfaces
  • Shock isolated UCL glass lens
  • Self charging glow-in-the-dark flashlight locator ring

 

 

Performance:

1 Cell

Name Letter Level # Power
Miliwatts Lumens
red R     6  
dim D 1 0.005% 1.5 0.18
low L 14 0.6% 180 20
medium M 21 10% 3000 346
high H 28 55% 17000 1933

 

2 Cells
Name Letter Level # Power
Miliwatts Lumens
red R     6  
dim D 1 0.005% 1.5 0.18
low L 16 1.4% 400 46
medium M 24 22% 6500 758
high H 33 100% 30000 3498

 

  1. values for initial settings, channels can be changed or disabled
    values are for XPL, 219B values are less (21w max)
  2. lumens rated from the LED, at 25C. OTF will be less
  3. stretch and battery protection turned on, see FG for more examples

 

Programmable Board Features:

  1. 0.18 lumen low: (weeks of candle bright runtime)
  2. 3500 lumen high: near 20,000x higher higher high than lowest low
  3. Battery swap mode groups (independent 1 and 2 cell modes)
  4. As few as 1 mode per group (1+1) and up to 4 per group (4+4)
  5. Program modes from among 33 white levels plus red (3+1 LEDs)
  6. SOS, strobe, and beacon (defaults are off).
    Beacon can be red or white with adjustable timing
  7. Mode memory: Off - On - Hybrid (default is off)
    Hybrid stores the last mode but cycles from mode 1 on the next change
  8. Battery stretch starts reducing output at 3.2v, down to 0.5w (default on)
    Until overdischarge protection kicks in at 2.8v (default is on)
  9. Bounce protection switches to red when to much light is reflected
    It also gives you direct access to red, as a 9th (4+4+1) mode (default off)
  10. Supports 1x ICR/IMR, 2x ICR/IMR, 2x CR123 (CR123 selected in advance)
    CR123 reduces output, changes stretch to 2.25v, & disables overdischarge
  11. CR123 can be used in emergencies without advanced programming.
    Just limit use to RDLM modes (levels 22 and 25 - under 5 watts per cell)
  12. Change temperature ceiling: 65C > 60C > 55C > 50C > 45C > 40C > 35C > 30C

 

Universal Board Features:

  1. Custom high effeciency boost driver and board
  2. Per cell battery voltage blink out (111 PIN)
  3. Serial number blink out with specs and firmware history (222 PIN)
  4. Dual light channels, 30w (3x white) + 7ma (1x red or amber)
  5. No PWM - sound and flicker free operation at all power levels
  6. Input voltage range from 2.5v to 8.8v (1-2 cells)
  7. Fully qualified between -40 and 248F (-40 and 120C)
  8. Reversed battery polarity protection
  9. Under and over voltage protection (2.5/8.8v)
  10. Adaptive temperature control (reduces output only 1/33rd as needed)
  11. Integrated thermal safety protection at 65C (149F)
  12. Integrated thermal overheating protection at 120C (248F)
  13. Shock proof materials, components, and design

 

Options:

1) Choose secondary LED (amber or red):

2) Choose primary LED (XPL for lumens, 219 for color)

3) Choose initial modes for 1 and 2 cells (can be programmed after delivery)

4) Choose GID for most uses, black ring for tactical uses (no glow)

 

Battery Notes:

2016-2017 AW 16340 cells only for high modes

Most 16340 (even older AW) cannot support full power

Cells not included, see options menus below for recommended cells

Do not use CR123 above Medium (10% on one cell, 22% on two)

IMR/INR recommended - use only cells rated above 6 amps

Avoid cells with huge capacity values (1200mah 18350, etc)

Stretch mode on and recommended for end of runtime taper

 

Switch Notes:

v5 requires 6+ amps for high mode operation

This is more than Z56/Z57 switches can reliably handle

Modified McClicky switches are recommened for all clicky applications:

 

CAUTIONS:

  • Do not leave unattended while running on high
  • This light creates excessive heat
  • This light may cause eye damage
  • This light may burn the skin at close range
  • This light may cause combustibles to ignite
  • This light is not a toy, keep away from children

 

 

Metal components made in  

Electronics made in


Design & CAD - Tom
 Engineering - Tom
Machining - Craig
Electronics - Serge
Assembly
- Dan

 


Product Options:

Finish Quality
GID Ring
Included Batteries
Light Engine
Modes

Product Code: TL-eHead-NT



Copyright 2010-2016 by OVEREADY, Inc.

SureFire(R) is a Registered Trademark of SureFire, LLC. The use of the Surefire(R) trademark, a registered
trademark of SureFire, LLC, is strictly for the purpose of identifying the host flashlight advertised
on this website. SureFire, LLC, which manufactures and sells Surefire(R) flashlights is not associated
in any way, form or fashion with OVEREADY, Inc. SureFire, LLC, does not sponsor, warrant, or endorse
any modified or customized products advertised on this website. Modifications and upgrades made by
OVEREADY, Inc. may void some or all of the SureFire(R) original manufacturers warranties.

All other trademarks, copyrights, and graphics or text not owned by OVEREADY, Inc. or any of its related
companies that appear on this site are the property of their respective owners, who may or may not be
affiliated with, connected to, or sponsored by OVEREADY, Inc.