BOSS 7075 HA Satin Black 35 Body

Description

Includes one 35 body only, with clip

• Carved from solid aluminum for a personalized finish
• Triad tail shape for both tail standing and easy thumb access
• Tapered body for superb grip and directional awareness
• Longitudinal channels and divots for rotational traction

Programmable Board Features:

1. 0.18 lumen low: (weeks of candle bright runtime)
2. 3500 lumen high: near 20,000x higher higher high than lowest low
3. Battery swap mode groups (independent 1 and 2 cell modes)
4. As few as 1 mode per group (1+1) and up to 4 per group (4+4)
5. Program modes from among 33 white levels plus red (3+1 LEDs)
6. SOS, strobe, and beacon (defaults are off).
   Beacon can be red or white with adjustable timing
7. Mode memory: Off – On – Hybrid (default is off)
   Hybrid stores the last mode but cycles from mode 1 on the next change
8. Battery stretch starts reducing output at 3.2v, down to 0.5w (default on)
   Until over-discharge protection kicks in at 2.8v (default is on)
9. Bounce protection switches to red when too much light is reflected
   It also gives you direct access to red, as a 9th (4+4+1) mode (default off)
10. Supports 1x ICR/IMR, 2x ICR/IMR, 2x CR123 (2x CR123 selected in advance)
    2x CR123 mode reduces output, changes stretch to 2.25v, & disables over-discharge
11. CR123 can be used in emergencies without advanced programming.
    Just limit use to RDLM modes (levels 22 and 25 – under 5 watts per cell)
12. Change temperature ceiling: 65C > 60C > 55C > 50C > 45C > 40C > 35C > 30C

Universal Board Features:

1. Custom high efficiency boost driver and board
2. Per cell battery voltage blink out (111 PIN)
3. Serial number blink out with specs and firmware history (222 PIN)
4. Dual light channels, 30w (3x white) + 7ma (1x red or amber)
5. No PWM – sound and flicker free operation at all power levels
6. Input voltage range from 2.5v to 8.8v (1-2 cells)
7. Fully qualified between -40 and 248F (-40 and 120C)
8. Reversed battery polarity protection
9. Under and over voltage protection (2.5/8.8v)
10. Adaptive temperature control (reduces output only 1/33rd as needed)
11. Integrated thermal safety protection at 65C (149F)
12. Integrated thermal overheating protection at 120C (248F)
13. Shock proof materials, components, and design

Performance:

MODELS

1 CELL

2 CELL

1. TorchLAB BOSS decides its own max output every time you use its output is controlled in real time by temperature and voltage monitors
   the hotter the environment and less the airflow, the lower the output and the longer the runtime. the colder the environment and the more the airflow, the higher the output and the shorter your runtime
2. values for initial settings, channels can be changed or disabled values are for XPL, 219C values are less (24w max)
3. lumens rated from the LED, at 25C. OTF will be less
4. stretch and battery protection turned on, see FG for more examples

Battery Notes:

• Do not use CR123 above Medium (10% on one cell, 22% on two)
• IMR/INR recommended – use only cells rated above 6 amps
• Stretch mode on and recommended for end of runtime taper

CAUTIONS

• Do not leave unattended while running on high
  
• IMR 18350 are recommended minimum
• INR 18650 are also recommended with longer bodies
• This light creates excessive heat
• This light may cause eye damage
• This light may burn the skin at close range
• This light may cause combustibles to ignite
• This light is not a toy, keep away from children